LINEVO Foshan Plant · 15,000+ m² · 50+ Patents · Since 2013
Jelly Packing MachineLINEVO Gel, Stick & Cup Lab
FAMILY: T03FORMAT: PARTICULATE-RICH FRUIT, CHIA & PULP GEL POUCHESMANUFACTURER: LINEVO (FOSHAN)

Multi-Lane Particulate Gel Pouch Machine for Fruit-Pulp & Seed Jellies

A multi-lane vertical gel pouch configuration built specifically for nutritional gels and fruit jellies that contain suspended particles—such as fruit pulp, chia seeds, nata de coco micro-cubes, or botanical granules—where standard narrow check-valves clog or shear inclusions.

01 // APPLICATION FIT SCREENING

What It Is Built For vs. When to Choose Another Configuration

USE IT FOR

Target Products & Production Duty

  • Functional jelly and sports nutrition producers dosing gels with suspended chia seeds, crushed fruit pulp, citrus cells, or small coconut/konjac inclusions.
  • Thick botanical, herbal, or fruit-paste pouches where valve port clearance must be matched to maximum particle diameter.
  • Multi-lane foil stick or shaped sachet production verified via Foshan sample pumping trials.
CHOOSE ANOTHER LINEVO MACHINE IF

Better-Matched Sibling Configurations

02 // TECHNICAL PARAMETERS & OPERATING CONDITIONS

Specification Table (Metric & Imperial)

ParameterMetric SpecificationImperial EquivalentOperating Condition & Verification Note
Equipment FamilyLINEVO T03 Particulate Gel Multi-Lane Series—Configured per project after testing your gel viscosity and maximum particle dimensions.
Applicable ProductsNutritional gels & fruit jellies containing suspended particles—Particle size (mm), soft vs. hard seed texture, and solids % must be shared for valve sizing.
Pack FormatsMulti-lane stick packs, 4-side sachets & shaped foil pouches—Each pouch width and contour die requires dedicated forming/cutting tooling.
Frame ConstructionStainless steel multi-lane vertical form-fill-seal frame—Hopper agitation, heating, and contact steel grade are specified in the quotation.

Shift Production Reality Note: Listed cycle speeds depend on container or bag volume, target fill weight, and material flow characteristics. For multi-shift plant planning, multiply nominal run rate by a 0.70–0.85 shift OEE factor (accounting for film/label splices, hopper refills, and routine cleaning) and confirm exact speed with your samples during Foshan FAT.

03 // MECHANICAL & CONTROLS BOUNDARY

What Is Included vs. What We Review With You

BASE MACHINE ARCHITECTURE

Core Station Scope

  • Multi-lane vertical pouch forming, longitudinal sealing, and cross-sealing/cutting chassis
  • Top product hopper and multi-lane volumetric dosing manifold
ENGINEERED PER PROJECT

Reviewed Against Your Samples & Plant

  • Application, format tooling, rotary valve port clearance, and nozzle bore engineered around your exact particle size
  • Hopper agitation speed/blade profile to keep seeds or pulp suspended without shearing
  • Lane count, parent film width, shaped-pouch die tooling, and site utilities
SUB-ASSEMBLY HARDWARE SPECIFICATION

Verified Electrical, Sensing & Pneumatic BOM

CONTROL CABINET // 01Siemens

PLC Motion & Sequence Controller

Main programmable logic controller coordinating multi-lane rotary piston dosing, film/cup indexing, jacket heating, and sealing interlocks.

TIMING & DC BUS // 02OMRON

Rotary Encoder, Control Relays & 24V Switching Power Supply

Phase-angle timing feedback, cabinet switching relays, and regulated 24V DC power supply across multi-lane stick, sachet, and cup stations.

OPERATOR & DRIVE // 03Delta Electronics

HMI Color Touchscreen & Variable Frequency Drive (VFD)

Multi-recipe touchscreen terminal storing lane dose/temperature profiles and inverter motor speed control for main drives and conveyors.

ANTI-DRIP PNEUMATICS // 04AirTAC

Pneumatic Cylinders, Solenoid Valves, Vacuum Gauge & FRL Unit

Suck-back anti-drip nozzle actuators, cross-sealing cylinders, manifold valves, pouch-opening vacuum gauge, and air preparation unit.

Representative electrical, sensing, and pneumatic hardware fitted on LINEVO packaging configurations; exact part series or project-specified alternatives are itemized in your written quotation BOM.

04 // OPERATING SEQUENCE & FLOOR RELIABILITY

How It Works & Mechanical Countermeasures to Common Line Failures

  1. 01
    Gentle Suspension Conditioning

    Particulate gel is held in the top hopper so seeds or fruit pulp remain evenly dispersed across feed ports.

  2. 02
    Multi-Lane Film Slitting & Forming

    Printed barrier rollstock slits into parallel lanes and forms stick or sachet bodies.

  3. 03
    Clearance-Matched Volumetric Dosing

    Valve ports and nozzles sized to your particulate dimensions meter each portion cleanly.

  4. 04
    Seal-Zone Clearance & Cutting

    Cross-sealing bars close between dose cycles to output hermetic particulate gel pouches.

Production Floor Failure Modes & LINEVO Countermeasures

Chia Seeds or Fruit Fibers Wedging Standard Check-Valves Open

Floor Risk: Spring ball-check valves trap a single seed on the seat, causing continuous dripping into the seal area on that lane.

Mechanical Countermeasure: LINEVO reviews your actual particulate sample in Foshan to size positive rotary-valve clearances and nozzle shut-offs that shear or pass particles cleanly.

Nozzle Bridging When Pulp Clumps Inside Narrow Stick Tubes

Floor Risk: Undersized 4 mm drop tubes bridge fibrous fruit puree when running narrow sticks.

Mechanical Countermeasure: Pouch width, forming tube ID, and nozzle bore are co-designed around maximum inclusion size before tooling freeze.

Float-or-Sink Separation Giving Pure Syrup First & Dense Pulp Last

Floor Risk: Citrus sacs float while dense seeds sink in unagitated tanks.

Mechanical Countermeasure: Hopper agitation geometry is matched to gel yield stress during engineering review.

Particulates Trapped Inside Cross-Seal Seams

Floor Risk: Late-falling pulp pieces land on hot seal bars, charring and creating burst failures.

Mechanical Countermeasure: Synchronizing pump stroke cutoff timing with intermittent film pull leaves a clean headspace gap above the gel column.

05 // PROCUREMENT & ACCEPTANCE PROTOCOL

Comparing Quotations? Check These 5 Things

01
Multi-Lane Cuts/Min × Shift OEE (0.70–0.85) vs. Dry Speed

Multiply cycle rate (20–40 cuts/min) by lane count and a realistic 0.70–0.85 shift OEE factor accounting for hot-fill hopper replenishment, parent reel splices, and CIP sanitation.

02
Hot-Fill Hopper Heating, Agitation & Anti-Drip Pump Scope

Verify whether double-walled jacketed heating, mixing paddles, rotary-valve piston dosing, and pneumatic suck-back shut-off nozzles are sized for your gel viscosity and particulate size.

03
Sanitary Steel Grade (SUS304 vs. SUS316L), Power & Air Split

Confirm product-contact steel grade for acidic fruit gels, electrical heater load (kW, voltage/phase), and dry compressed air consumption (0.6–0.8 MPa) on the written scope sheet.

04
Parent Film Slitting Width, Forming Tubes & Cut Tooling

Check parent rollstock maximum width (420 / 500 / 700 / 980 mm), lane pitch, tear-notch punch geometry, and cup cavity rings against approved dieline drawings before plate engraving.

05
Pre-Shipment Foshan FAT Leak & Seal-Contamination Trial

Require a filmed Foshan FAT running viscous gel or gummy samples at target fill temperature to verify zero seal-zone stringing, weight uniformity across lanes, and burst resistance.

PRE-DISPATCH PROJECT SEQUENCE

From Sample Audit to Foshan FAT & Export Commissioning

  1. 01Sample Audit

    Send physical containers, pouches, lids, film reels, or product specs to Foshan so engineers verify dimensions, flow behavior, and station geometry.

  2. 02Written Scope Freeze

    Confirm exact model/lane count, included vs. project-reviewed modules, electrical/air utilities, and format parts in the technical quotation.

  3. 03Foshan Fabrication & Wiring

    CNC machining, stainless frame assembly, PLC/HMI programming, and inline station synchronization inside LINEVO's 15,000+ m² Foshan plant.

  4. 04Foshan FAT Run Before Shipment

    Full-speed trial on sample materials verifying registration, dosing/vacuum stability, seal integrity, and fault interlocks on video or in person.

  5. 05Export Crating & Commissioning

    Fumigation-free export crating, English schematics, parameter backups, wear-part list, and remote video or scheduled on-site commissioning.

06 // MACHINE-SPECIFIC ENGINEERING ANSWERS

Frequently Asked Questions

What is the maximum fruit cube or seed size a multi-lane gel pouch can accept?

Maximum particle diameter depends directly on finished pouch width and internal nozzle bore—narrow 20 mm sticks fit fine seeds/pulp (1–3 mm), whereas wider 4-side sachets or cups handle larger fruit dices. Ship samples to Foshan for pump clearance verification.

When should we switch from multi-lane pouches to a cup fill-seal machine?

If your recipe contains whole fruit segments, large nata de coco cubes (>6–8 mm), or layered pudding tops, our Automatic CIP Cup Filling & Sealing Machine provides wide open-top filling.

Can we run both smooth gels and particulate gels on this machine?

Yes—rotary piston channels sized for small particulates also meter smooth viscous gels accurately via HMI stroke adjustment.

DIRECT FOSHAN FACTORY ENGINEERING

Request Layout Drawing & Sample Trial for Multi-Lane Energy Gel Pouch Machine for Particulate-Rich Nutritional Gels

Share your pack dimensions, target fill volume/weight, gel dosing temperature, shift output, and local electrical grid (voltage/Hz). LINEVO engineers confirm exact lane/cavity tooling and Foshan FAT schedule without obligation.