LINEVO Foshan Plant · 15,000+ m² · 50+ Patents · Since 2013
Jelly Packing MachineLINEVO Gel, Stick & Cup Lab
FAMILY: T03FORMAT: SANITARY 4-SIDE-SEAL SPORTS GEL & SUPPLEMENT SACHETSMANUFACTURER: LINEVO (FOSHAN)

Sanitary Multi-Lane 4-Side-Seal Sports Gel & Liquid Supplement Sachet Machine

A mirror-polished SUS316/304 multi-lane four-side-seal sachet machine engineered for endurance sports gels, electrolyte shots, and liquid dietary supplements—combining a double-walled heated agitated hopper, rotary piston pump matrix, pneumatic suck-back nozzles, and CIP-ready sanitary pipelines.

01 // APPLICATION FIT SCREENING

What It Is Built For vs. When to Choose Another Configuration

USE IT FOR

Target Products & Production Duty

  • Endurance sports nutrition and nutraceutical brands filling viscous carbohydrate gels, liquid electrolyte concentrates, hydration shots, and amino acid blends into 4-side-seal sachets.
  • cGMP-oriented supplement co-packers requiring mirror-polished SUS316/304 stainless steel contact surfaces and CIP clean-in-place wash loops.
  • High-mix contract plants switching rapidly between botanical syrups, collagen liquids, and thick functional gels.
CHOOSE ANOTHER LINEVO MACHINE IF

Better-Matched Sibling Configurations

02 // TECHNICAL PARAMETERS & OPERATING CONDITIONS

Specification Table (Metric & Imperial)

ParameterMetric SpecificationImperial EquivalentOperating Condition & Verification Note
Sachet Seal FormatMulti-lane four-side-seal flat sachet—Sachet width, length, and lane count are configured around your supplement dose and artwork.
Sanitary Material & FinishSUS316/SUS304 stainless steel · Mirror-polished contact build + CIP—Built for acidic electrolyte, vitamin, and botanical liquid supplements.
Volumetric DosingIndependent multi-lane rotary piston pumps—Fill settings and discharge behavior are validated with your gel sample in Foshan.
Anti-Drip CutoffPneumatic suck-back shut-off nozzle per lane—Keeps 4-side foil seams free of sticky carbohydrate residue.
Hopper ConditioningDouble-walled jacketed electric thermal hopper + agitator paddles—Holds uniform temperature and suspension across multi-hour runs.

Shift Production Reality Note: Listed cycle speeds depend on container or bag volume, target fill weight, and material flow characteristics. For multi-shift plant planning, multiply nominal run rate by a 0.70–0.85 shift OEE factor (accounting for film/label splices, hopper refills, and routine cleaning) and confirm exact speed with your samples during Foshan FAT.

03 // MECHANICAL & CONTROLS BOUNDARY

What Is Included vs. What We Review With You

BASE MACHINE ARCHITECTURE

Core Station Scope

  • Mirror-polished SUS316/304 chassis, product delivery pipelines, and CIP clean-ready manifold
  • Double-walled jacketed heated hopper with heavy-duty mechanical mixing paddles
  • Multi-lane rotary piston dosing pumps and pneumatic suck-back anti-dripping nozzles
ENGINEERED PER PROJECT

Reviewed Against Your Samples & Plant

  • Advanced Mechanical/Servo Rotary Piston Pump Matrix stroke volume and lane count
  • 4-side-seal roller profiling, tear-notch / rounded-corner cutter, and parent-web batch coding
  • CIP return connection sizing and site electrical/compressed-air utilities
SUB-ASSEMBLY HARDWARE SPECIFICATION

Verified Electrical, Sensing & Pneumatic BOM

CONTROL CABINET // 01Siemens

PLC Motion & Sequence Controller

Main programmable logic controller coordinating multi-lane rotary piston dosing, film/cup indexing, jacket heating, and sealing interlocks.

TIMING & DC BUS // 02OMRON

Rotary Encoder, Control Relays & 24V Switching Power Supply

Phase-angle timing feedback, cabinet switching relays, and regulated 24V DC power supply across multi-lane stick, sachet, and cup stations.

OPERATOR & DRIVE // 03Delta Electronics

HMI Color Touchscreen & Variable Frequency Drive (VFD)

Multi-recipe touchscreen terminal storing lane dose/temperature profiles and inverter motor speed control for main drives and conveyors.

ANTI-DRIP PNEUMATICS // 04AirTAC

Pneumatic Cylinders, Solenoid Valves, Vacuum Gauge & FRL Unit

Suck-back anti-drip nozzle actuators, cross-sealing cylinders, manifold valves, pouch-opening vacuum gauge, and air preparation unit.

Representative electrical, sensing, and pneumatic hardware fitted on LINEVO packaging configurations; exact part series or project-specified alternatives are itemized in your written quotation BOM.

04 // OPERATING SEQUENCE & FLOOR RELIABILITY

How It Works & Mechanical Countermeasures to Common Line Failures

  1. 01
    Thermal & Agitated Blending

    Viscous sports gel or supplement concentrate stays warm and homogeneous in the jacketed SUS316/304 hopper.

  2. 02
    Dual-Layer Web Slitting & Alignment

    Barrier foil laminate slits and aligns into parallel 4-side sachet tracks.

  3. 03
    Positive Rotary Piston Metering

    Each lane's rotary piston meters an exact hydration or carb shot, closing with pneumatic suck-back.

  4. 04
    Four-Side Hermetic Sealing & Discharge

    Longitudinal and cross seal bars fuse flat four-edge borders cleanly for pocket-ready endurance packs.

Production Floor Failure Modes & LINEVO Countermeasures

Citric & Malic Acid Electrolytes Pitting Standard 304 Valves

Floor Risk: Low-pH sports gels (pH 2.8–3.8) with chloride electrolytes corrode unpolished fittings.

Mechanical Countermeasure: Mirror-polished SUS316/304 sanitary contact pipelines and valves resist acid/electrolyte corrosion and flush clean via CIP.

Micro-Channel Leaks in Runner Jersey Pockets Under Body Weight

Floor Risk: Tiny sugar droplets trapped in side or top seams create pinholes when athletes sit on or squeeze endurance gel packs.

Mechanical Countermeasure: Pneumatic suck-back nozzles eliminate post-fill drips so all four foil edges fuse dry and burst-tight.

Active Amino Acids or Botanicals Settling During Shift Runs

Floor Risk: Static holding tanks let dense mineral or herbal fractions sink, skewing active potency from start to end of batch.

Mechanical Countermeasure: Heavy-duty mechanical mixing paddles inside the jacketed hopper maintain uniform suspension.

Viscosity Spikes Slowing Cold Morning Startups

Floor Risk: Chilled glucose/maltodextrin gels cavitate piston pumps until lines warm up.

Mechanical Countermeasure: Constant electric jacket heating keeps fluid velocity consistent from the first cut.

05 // PROCUREMENT & ACCEPTANCE PROTOCOL

Comparing Quotations? Check These 5 Things

01
Multi-Lane Cuts/Min × Shift OEE (0.70–0.85) vs. Dry Speed

Multiply cycle rate (20–40 cuts/min) by lane count and a realistic 0.70–0.85 shift OEE factor accounting for hot-fill hopper replenishment, parent reel splices, and CIP sanitation.

02
Hot-Fill Hopper Heating, Agitation & Anti-Drip Pump Scope

Verify whether double-walled jacketed heating, mixing paddles, rotary-valve piston dosing, and pneumatic suck-back shut-off nozzles are sized for your gel viscosity and particulate size.

03
Sanitary Steel Grade (SUS304 vs. SUS316L), Power & Air Split

Confirm product-contact steel grade for acidic fruit gels, electrical heater load (kW, voltage/phase), and dry compressed air consumption (0.6–0.8 MPa) on the written scope sheet.

04
Parent Film Slitting Width, Forming Tubes & Cut Tooling

Check parent rollstock maximum width (420 / 500 / 700 / 980 mm), lane pitch, tear-notch punch geometry, and cup cavity rings against approved dieline drawings before plate engraving.

05
Pre-Shipment Foshan FAT Leak & Seal-Contamination Trial

Require a filmed Foshan FAT running viscous gel or gummy samples at target fill temperature to verify zero seal-zone stringing, weight uniformity across lanes, and burst resistance.

PRE-DISPATCH PROJECT SEQUENCE

From Sample Audit to Foshan FAT & Export Commissioning

  1. 01Sample Audit

    Send physical containers, pouches, lids, film reels, or product specs to Foshan so engineers verify dimensions, flow behavior, and station geometry.

  2. 02Written Scope Freeze

    Confirm exact model/lane count, included vs. project-reviewed modules, electrical/air utilities, and format parts in the technical quotation.

  3. 03Foshan Fabrication & Wiring

    CNC machining, stainless frame assembly, PLC/HMI programming, and inline station synchronization inside LINEVO's 15,000+ m² Foshan plant.

  4. 04Foshan FAT Run Before Shipment

    Full-speed trial on sample materials verifying registration, dosing/vacuum stability, seal integrity, and fault interlocks on video or in person.

  5. 05Export Crating & Commissioning

    Fumigation-free export crating, English schematics, parameter backups, wear-part list, and remote video or scheduled on-site commissioning.

06 // MACHINE-SPECIFIC ENGINEERING ANSWERS

Frequently Asked Questions

When do endurance gel brands pick a 4-side-seal sachet (dession-118) vs. a back-seal stick (dession-117)?

Flat 4-side-seal sachets give a wider front billboard for nutrition panels and sit flat in running belts, while back-seal tubular sticks use slightly narrower film per ml for one-hand squeeze consumption.

Can this machine run shaped bottle-top spout necks on 4-side sachets?

Yes—share your shaped sachet dieline (such as tear-off drink-spout tops) so rotary/die punch tooling and waste-trim extraction are engineered into the quotation.

How is CIP cleaning executed on the multi-lane pump manifold?

The sanitary SUS316/304 delivery manifold connects to your plant CIP supply to circulate hot water/caustic/rinse cycles through the hopper, pistons, and nozzles without full manual teardown.

DIRECT FOSHAN FACTORY ENGINEERING

Request Layout Drawing & Sample Trial for Sanitary Multi-Lane Liquid Sachet Packing Machine for Sports Gel and Supplements

Share your pack dimensions, target fill volume/weight, gel dosing temperature, shift output, and local electrical grid (voltage/Hz). LINEVO engineers confirm exact lane/cavity tooling and Foshan FAT schedule without obligation.