LINEVO Foshan Plant · 15,000+ m² · 50+ Patents · Since 2013
Jelly Packing MachineLINEVO Gel, Stick & Cup Lab
FAMILY: T01FORMAT: HIGH-SPEED ROLLSTOCK PILLOW & GUSSET GUMMY BAGSMANUFACTURER: LINEVO (FOSHAN)

Large VFFS Gummy Candy & Jelly Multipack Machine with Anti-Stick Weighing

A heavy-duty vertical form-fill-seal (VFFS) bagging tower paired with multihead combination weighing and Z-bucket elevation—engineered with servo-driven film pulling and pneumatic cross-sealing mechanisms to pack hygroscopic gummy candies, fruit chews, and bulk jelly multipacks into moisture-tight pillow and gusseted bags.

01 // APPLICATION FIT SCREENING

What It Is Built For vs. When to Choose Another Configuration

USE IT FOR

Target Products & Production Duty

  • Confectionery plants running high-volume pillow or side-gusset bags of gummy bears, fruit chews, jelly beans, and wrapped mini jellies from economical rollstock film.
  • Hygroscopic pectin and gelatin formulations requiring hermetic multi-layer barrier film seals against moisture uptake, clumping, and melting.
  • Bulk foodservice bags and high-speed retail packs where rollstock cost per bag beats premade pouches.
CHOOSE ANOTHER LINEVO MACHINE IF

Better-Matched Sibling Configurations

02 // TECHNICAL PARAMETERS & OPERATING CONDITIONS

Specification Table (Metric & Imperial)

ParameterMetric SpecificationImperial EquivalentOperating Condition & Verification Note
Equipment FamilyLINEVO T01 Heavy-Duty Confectionery VFFS Series—Complete Z-elevator + multihead weigher + vertical form-fill-seal tower.
Film Pull & Sealing DriveServo-driven film pulling + pneumatic cross-sealing mechanisms—Configured for multi-layer moisture-barrier confectionery films.
Target ProductsGummy candies, fruit chews, jelly beans, hard candies & jelly multipacks—Oiled vs. sanded sugar surface coating is tested on dimpled weigher pans in Foshan.
Bag FormatsPillow bags & side-gusseted bulk/retail bags—Each bag width requires its dedicated stainless forming collar.
Speed, Bag Range & UtilitiesConfigured per target bag weight & ceiling clearance—Companion gummy VFFS setups run 30–70 bags/min depending on bag size; exact parameters stated in quotation.

Shift Production Reality Note: Listed cycle speeds depend on container or bag volume, target fill weight, and material flow characteristics. For multi-shift plant planning, multiply nominal run rate by a 0.70–0.85 shift OEE factor (accounting for film/label splices, hopper refills, and routine cleaning) and confirm exact speed with your samples during Foshan FAT.

03 // MECHANICAL & CONTROLS BOUNDARY

What Is Included vs. What We Review With You

BASE MACHINE ARCHITECTURE

Core Station Scope

  • Stainless VFFS bagging unit with forming collar carriage, longitudinal sealer, and pneumatic cross-sealing jaws
  • Servo-driven film pulling belt assembly
ENGINEERED PER PROJECT

Reviewed Against Your Samples & Plant

  • Servo-driven film pulling and pneumatic cross-sealing pressure tuned to your barrier laminate thickness
  • Anti-sticking dimpled 10-head or 14-head multihead weigher, Z-bucket elevator, and stainless support platform
  • Forming collars per bag width, inline TTO/ribbon date coder, and plant voltage/air supply
SUB-ASSEMBLY HARDWARE SPECIFICATION

Verified Electrical, Sensing & Pneumatic BOM

CONTROL CABINET // 01Siemens

PLC Motion & Sequence Controller

Main programmable logic controller coordinating multi-lane rotary piston dosing, film/cup indexing, jacket heating, and sealing interlocks.

TIMING & DC BUS // 02OMRON

Rotary Encoder, Control Relays & 24V Switching Power Supply

Phase-angle timing feedback, cabinet switching relays, and regulated 24V DC power supply across multi-lane stick, sachet, and cup stations.

OPERATOR & DRIVE // 03Delta Electronics

HMI Color Touchscreen & Variable Frequency Drive (VFD)

Multi-recipe touchscreen terminal storing lane dose/temperature profiles and inverter motor speed control for main drives and conveyors.

ANTI-DRIP PNEUMATICS // 04AirTAC

Pneumatic Cylinders, Solenoid Valves, Vacuum Gauge & FRL Unit

Suck-back anti-drip nozzle actuators, cross-sealing cylinders, manifold valves, pouch-opening vacuum gauge, and air preparation unit.

Representative electrical, sensing, and pneumatic hardware fitted on LINEVO packaging configurations; exact part series or project-specified alternatives are itemized in your written quotation BOM.

04 // OPERATING SEQUENCE & FLOOR RELIABILITY

How It Works & Mechanical Countermeasures to Common Line Failures

  1. 01
    Bucket Elevation & Anti-Stick Dispersion

    Gummies or wrapped mini jellies ride the Z-bucket elevator to the top dispersion cone and dimpled radial feeders.

  2. 02
    High-Speed Combination Weighing

    Multihead buckets calculate the closest gram combination instantaneously and drop cleanly down steep chutes.

  3. 03
    Servo Rollstock Tube Forming

    Multi-layer moisture-barrier film pulls smoothly over the forming collar via servo belts and seals longitudinally.

  4. 04
    Pneumatic Hermetic Cross-Sealing

    Pneumatic jaws clamp and fuse moisture-tight top/bottom seals before discharging finished bags.

Production Floor Failure Modes & LINEVO Countermeasures

Carnauba-Oiled or Humid Pectin Gummies Clinging Inside Weigher Buckets

Floor Risk: Sticky gummies hang up on flat metal hoppers, causing missed dumps and erratically underweight bags.

Mechanical Countermeasure: Pairing embossed anti-sticking dimpled radial pans, buckets, and steep chutes keeps tacky gummies moving cleanly.

Humidity Ingress Turning Bottled/Bagged Gummies Into One Fused Clump

Floor Risk: Weak fin or cross seams on thin OPP films let warehouse moisture sweat hygroscopic sugar/pectin gummies.

Mechanical Countermeasure: Servo film pulling handles thick metallized/high-barrier laminates while pneumatic cross jaws lock moisture-tight seams.

Bouncing Gummies Getting Crushed Inside Closing Cross-Seal Jaws

Floor Risk: Long vertical drop distances scatter stray pieces across the seal line on fast cycles.

Mechanical Countermeasure: Staggered weigher dump timing and product-settling dwell synchronize cleanly with jaw closure.

Bag Length Drift When Switching Printed Confectionery Rollstock

Floor Risk: Mechanical clutch pullers slip as roll diameter shrinks.

Mechanical Countermeasure: Servo-driven film pulling paired with photoelectric eye-mark tracking holds consistent cut registration.

05 // PROCUREMENT & ACCEPTANCE PROTOCOL

Comparing Quotations? Check These 5 Things

01
Multi-Lane Cuts/Min × Shift OEE (0.70–0.85) vs. Dry Speed

Multiply cycle rate (20–40 cuts/min) by lane count and a realistic 0.70–0.85 shift OEE factor accounting for hot-fill hopper replenishment, parent reel splices, and CIP sanitation.

02
Hot-Fill Hopper Heating, Agitation & Anti-Drip Pump Scope

Verify whether double-walled jacketed heating, mixing paddles, rotary-valve piston dosing, and pneumatic suck-back shut-off nozzles are sized for your gel viscosity and particulate size.

03
Sanitary Steel Grade (SUS304 vs. SUS316L), Power & Air Split

Confirm product-contact steel grade for acidic fruit gels, electrical heater load (kW, voltage/phase), and dry compressed air consumption (0.6–0.8 MPa) on the written scope sheet.

04
Parent Film Slitting Width, Forming Tubes & Cut Tooling

Check parent rollstock maximum width (420 / 500 / 700 / 980 mm), lane pitch, tear-notch punch geometry, and cup cavity rings against approved dieline drawings before plate engraving.

05
Pre-Shipment Foshan FAT Leak & Seal-Contamination Trial

Require a filmed Foshan FAT running viscous gel or gummy samples at target fill temperature to verify zero seal-zone stringing, weight uniformity across lanes, and burst resistance.

PRE-DISPATCH PROJECT SEQUENCE

From Sample Audit to Foshan FAT & Export Commissioning

  1. 01Sample Audit

    Send physical containers, pouches, lids, film reels, or product specs to Foshan so engineers verify dimensions, flow behavior, and station geometry.

  2. 02Written Scope Freeze

    Confirm exact model/lane count, included vs. project-reviewed modules, electrical/air utilities, and format parts in the technical quotation.

  3. 03Foshan Fabrication & Wiring

    CNC machining, stainless frame assembly, PLC/HMI programming, and inline station synchronization inside LINEVO's 15,000+ m² Foshan plant.

  4. 04Foshan FAT Run Before Shipment

    Full-speed trial on sample materials verifying registration, dosing/vacuum stability, seal integrity, and fault interlocks on video or in person.

  5. 05Export Crating & Commissioning

    Fumigation-free export crating, English schematics, parameter backups, wear-part list, and remote video or scheduled on-site commissioning.

06 // MACHINE-SPECIFIC ENGINEERING ANSWERS

Frequently Asked Questions

Should we pack gummies on this VFFS rollstock tower or the LV-210 premade zipper machine?

Choose VFFS when lowest film cost per bag and higher pillow-bag speed (up to 70 bpm on small packs) drive unit economics; choose LV-210 when marketing requires freestanding resealable press-to-close zipper doypacks.

What ceiling height is needed for the Z-elevator + multihead weigher + VFFS tower?

Complete tower height typically spans 3.4–4.2 meters depending on weigher size and VFFS frame; share your room clear height so LINEVO configures standard or low-profile inclined infeed layouts.

Can this VFFS pack individually sealed konjac sticks into 20-count outer bags?

Yes—counting/weighing sealed sticks or mini cups into pillow outer multipacks is a common secondary packaging configuration; send sample sticks for Foshan chute flow testing.

DIRECT FOSHAN FACTORY ENGINEERING

Request Layout Drawing & Sample Trial for Large Vertical Form Fill Seal Machine for Gummy Candies & Confectionery

Share your pack dimensions, target fill volume/weight, gel dosing temperature, shift output, and local electrical grid (voltage/Hz). LINEVO engineers confirm exact lane/cavity tooling and Foshan FAT schedule without obligation.